I have a 1972 Nitro 295 "project" that I have and I need to sell it as I'm out of room. It needs lots of TLC but it's mostly all there. It has the correct S motor and ram horn exhaust. Plus I have a 73 S motor and "suitcase" exhaust that will go with it. I'll try to find some photos and post them later. Asking $500 and I will NOT ship it. I can meet you part way but will only go about 75 miles from Rutland, VT! If you are interested in it e-mail me (email@example.com) and we'll go from there.
Rupp Daddy: Yes Cyberlynx these are the ones i believe part is on #31995 on spindle have to look hard should be on the shaft that goes into the bulkhead. what you asking? if they correct ones??
Dec 27, 2013 18:51:13 GMT -6
BeatUpRupp: What's the best way to remove skis on 73 Nitro? I though removing the bolt through the spindle and shock would be easiest ... but it's very stuck
Jan 1, 2014 18:04:37 GMT -6
365rec: I had a difficult ski to remove also. I ended up using my grinder cutthe outside head off then a tapped with air hammer to get a lttle more movement.Add last splach of PB Blaster. then added 3 washers to the back side of the nut then started to tighten POP
Jan 5, 2014 9:54:56 GMT -6
lemans1955: What he said, had one stuck in my 73 American, cut the bolt head off, let it soak overnight in BP Blaster, then Heated the crap out of it. It only took about 500 hits with a hammer and die to get it out after that.
Jan 6, 2014 17:54:00 GMT -6
oldtimer46: Where is the serial number on a sprint 23?
Jan 7, 2014 8:34:09 GMT -6
BeatUpRupp: Thanks guys, that's what I was afraid of! Guess I'll grab the cut off wheel...
Jan 7, 2014 20:42:16 GMT -6
lemans1955: I guess if I really wanted to I could have taken the spindle off the sled and machined it out. But I'm stubborn like that lol
Jan 9, 2014 20:54:53 GMT -6
365rec: I have a bare chassis on the Alouette. When Repair the forward member for rust decay. Is it better to cut and weld in new or add metal over top reinforcing the weak area?
Jan 12, 2014 12:43:57 GMT -6
ruppluver: Any area that is rusting or decayed,will not be reinforced by adding new metal over the top.Actually it will keep rusting by leaving the old metal in.Cut out the bad,put in new.
Jan 12, 2014 13:47:49 GMT -6
365rec: Thank you When in doubt cut it out. Plasma Away!.
Jan 16, 2014 15:04:26 GMT -6
365rec: Who's going to Lakeview MI Winterfest? Anyone ever been?
Jan 16, 2014 15:05:41 GMT -6
jimgrandmi: I have been to the Lakeview MI Winterfest. The show is right on the main street, blocked off for sleds! Too Cool. The show is good and there are vintage oval races on the Tamarack Lack sponsored by BEVRA.
Jan 17, 2014 14:33:25 GMT -6
365rec: My aloutte skid and rear shock assembly are back from blasting. Preping for Paint and Smoothing the rough Edges.
Jan 20, 2014 13:54:42 GMT -6
BeatUpRupp: Denton Hill PA Hill Climbs this weekend! :-)
Jan 30, 2014 13:23:47 GMT -6
sprintmania: pb blaster and a air hammer
Feb 6, 2014 20:18:01 GMT -6
sprintmania: for the ski remove problem
Feb 6, 2014 20:18:47 GMT -6
BeatUpRupp: Thanks for the suggestion Sprintmania. I can definitely do that!
Feb 7, 2014 18:08:59 GMT -6
rupp23sprint: Not sure, dont see many i guess. If you have some, i would buy one from you.
Feb 27, 2014 12:43:44 GMT -6
rupp: I recently purchased a 1971 400 Magnum that has been updated to 1972 clamp on ram horn exhaust. I discovered that one of the pipes has several holes. Does anyone have a contact that could have a 1972 Nitro 400 0r 44 rams horn exhaust pipe?
Mar 9, 2014 6:45:13 GMT -6
randyrupplegs: I have a very nice original Rupp Centaur I would like to sell. I live in Sun Prairie, Wi.(near Madison). Sharp original with clear title. Calls only please. 608-445-9418 Pics to be sent to your emails only.
Mar 11, 2014 7:22:41 GMT -6